DECOSIL

DECOSIL is a Speciality Paint based on selected acrylic polymers, which impart unique properties to the paint. Some of these properties are :

1. It has excellent adhesion to most building materials such as wood, concrete, asbestos,
cement sheets, aluminium, marble china mosaic, etc.

2. It renders the coated surface completely impervious to water.

3. It prevents the growth of Mildew and Fungus thus retaining the aesthetics of the building.

4. It gives a pleasant satin finish.

5. It can withstand the expansion and contraction of concrete due to changes in weather conditions.

6. It can withstand high temperatures upto 80°C without cracking or softening.

7. It is single component and can be applied by conventional methods.

8. It has excellent durability on both interior and exterior surfaces.

9. It is ideal for exterior walls as it has long durability and excellent satin finish. It improvethe aesthetics of the structure and resists growth of fungus. It also does not fade due to light and rain.

Precautions :
1. Do not apply on damp surfaces.
2. Use in well-ventilated place.
3. Contains flammable solvents, keep away from heat and naked flames.
4. Close the lid tightly when not in use.
5. Do not use mineral turpentine for thinning.
6. Clean up : Use aromatic solvents or our special thinner.

Method of Application :
Lightly wire brush the surface to remove dust and loose . Oil or grease if any, should be cleaned with solvents. Old concrete surfaces should be with very dilute Hydrochloric Acid, then rinsed clean water and allowed to dry completely. Dilute , if necessary, with about 15 to 20%, Decosil No.91, stir the contents well and apply with a brush. Allow to dry for 4 to 8 hours before applying a coat.

Warranty :
The information contained in this leaflet is based on experience and laboratory tests and true to the of our knowledge. However, no warranty, express implied, arising out of the use of our product is as the conditions of use are beyond the control manufacturers of this product. Customers are to carry out their own tests to judge the of our product for the recommended.

NEOPRIME

"NEOPRIME" is a two pack polyester polyurethane primer system that is capable of providing highly durable coating systems for serve exposure conditions. These solvent borne formulations are prepared at relatively low-film-build component with a paint system typically comprising a primer and two coats of Top-Coat.

As a Non-toxic primer it also provides a mechanical key between the Primer and the Finishing coats as well as to increase the build of the paint system. The Primer prevents the subsrtate from attack of mild acids, alkalis, water and humidity and is therefore used as a priming coat in all substrates.

SPECIFICATIONS & TECHNICAL DATA :

    Above properties values represent typical results only and are not to be considered specifications.

NEOTEX Paints were developed keeping in mind ultimate requirements in protective and decorative applications of paints on wooden surface in TEXTURISED and SMOOTH finishes for interior applications.

NEOTEX paint is polyester modified high build top coat systems with fast curing properties which gives an opaque finish to a wooden surface in range of beautiful shades both in TEXTURED & SMOOTH finish. Coating Produced by NEOTEX paint demonstrate excellent water resistance, chemical & stain resistance performance exceeds that of traditional Nitrocellulose Paint and other hard thermoplastic coatings.

NEOTEX paint is a two pack system with Base Hardner which gives a tough and lasting protection to wood when it is applied over a WOOD PRIME penetration Primer. This exceptional properties of NEOTEX make it suitable for many factory applied wood coating as well as high performance kitchen cabinet finishes.

SUGGESTED APPLICATIONS :-
- Office and computer wooden furniture.
- Wooden cabinets, doors, etc.
- Kitchen Furniture.
- Interior Wooden Decoration.

KEY BENEFITS :-
- 20 mits surface dry time.
- 2 hours tack free time.
- 4 hours Recoat time if necessary with excellent sandability.
- Water Clean up.
- Protects from termites, pest attack & climate changes.
- Excellent adhesion.
- Very good chemical and stain resistance on 7 days cure.
- Very good mark resistance
- In variety of shades in TEXTURDED, GLOSSY & MATT Finishes

PRODUCT DATA :-

Polyester Amino Resin systems.

Solvents

Alcohols, Esters.

Fire Risk

Highly flammable.

Gloss

10% max @ 60 c

Non volatile contents (Theoretical)

55%

Specific Gravity

1.10 ± 0.02

Viscosity

100 ± 10" @ 30 c B4

Drying Properties :         Surface dry                   20 mts.

                                     Tack Free                    2 hours.

                                     Hard dry                      24 hours.

Application

Covering Capacity (theoretical)

60 Sq/Feet/Litre.

Pencil Hardness

2H

APPLICATION PROCEDURE FOR WOOD PRIMER AND FINISH COAT
SEALING :-

1) The wooden surface to be painted must be dry and free from dust and loose particles. Prepare the smooth surface by sanding with Emery Paper No.320. clean the surface free of loose Particles and dust.

2) Apply wood filler if necessary with Putty knife to smoothen minor unevenness of the surface and allow it to dry and remove excess filler by Emery Paper No.320 to smooth finish.

WOOD PRIMER :-
3) Apply one coat of Wood Primer after mixing Base and Hardner with Thinner. Allow it to dry for 6-8 hours. Scuff it with Emery Paper No.320 to remove raised gains. If the pores are still not filled, apply a second coat and follow the same step.

FINISH COAT :-
4) Select the finish coat available in shade in Matt. These finishes are two pack system supplied as base and Hardner.
Mix thoroughly Base & Hardner in recommended mixing ratio and thin down with Thinner. Apply one coat of finish Coat. Allow 5-6 hours between Coats if Second coat necessary. Allow the final finish coat to dry overnight. A completely clean surface is mandatory to ensure inter-coat adhesion, especially at long recoat interval.

MIXING RATIO :-
WOOD PRIMER & FINISH COAT are two component system consisting of a Base and Hardner.
Mix thoroughly 100 parts of Base with 10 parts of Hardner by volume in plastic or glass container stir the mixture thoroughly. Add 15 to 20 Parts of Thinner. The mixture should be used within 1-0 hours of mixing. Allow the final finish coat to dry overnight.

SPRAY APPLICATIONS & DRYING TIPS :-

1) Recommended air pressure for spray application is 25-40 # 1bs per sq. inch depends upon type of assembly.

2) The Control of the amount, Pressure and cleanliness of the air going to the spray gun is of critical importance in the system as air contains small but harmful quantities of water, oil, dirt and other contaminants which will lessen the quality of the sprayed finish and the air will likely vary in pressure during spraying job.
Air Control regulator or Air transformer perform function of air filtering, cleaning, air pressure regulation and indication of Pressure.

3) Air Transformer and Compressor tank should be drained before starting spraying operation and if necessary more than once if humidity level in air is higher than normal.

4) This is air drying system with surface drying time of 15-20 min. and Hard dry of 24-48 hours.

SAFETY INSTRUCTIONS AND OTHER INFORMATIONS :-

1) Spray finishing creates a certain amount of overspray, hazardous vapour and toxic fumes. This is true even under ideal conditions and there is no way to avoid it entirely.
For this reasons Respirators are essential during Spraying operation. Organic vapor Respirator with Protective goggles are recommended with spray Booth chambers.

2) This is a flammable material. Keep away from heat, sparks, etc. Store in dry place with adequate ventilation.

3) Always stir contents well and strain through muslin cloths (white). Close the container tightly after removing required quantity of Base, Hardner and Thinner.

4) It is a must to use separate containers (glass or plastics) for weighing Base and Hardner. Do not transfer the mixed Paint (Base + Hardner) Back to original Base container as it will spoil whole paint in the containers.

5) It is recommended to mix only the required amount of Base and Hardner which is needed for spraying as the pot life of mixed Paint is low.

WARRANTY :
The information contained in this leaflets is based on our experience and laboratory tests and true to the best of our knowledge. However, no warranty, express or implied, arising out of the use of our product is given as the conditions of use are beyond the control of manufacturers of this product. Customers are advised to carry out their own tests to judge the suitability of our product for the recommended applications.

Two component POLYURETHANE Clear & Pigmented coating were developed keeping in mind ultimate requirements in protective and decorative application with enhanced performance properties like :-

• Good gloss retention unsurpassed by any other air drying system and can be highly recommended for high U. V. conditions.

• Good resistant to Acids, Alkalis, Salt spray, solvents, lubricants and weathering properties like saline and marine atmosphere.

• Ability to produce good films at room temperature equipment to those obtained from stoving paint with major gain in energy conservation.

• Coating are more abrasion resistance with long life flexibility, impact resistance, stain resistance, scratch resistance properties.

• Easy to apply and fast drying.

• Good dielectric properties.

• In automotive Industry, particularly in the vehicle repair as it gives a more rapid hardening than other refinish paints with high gloss film with good scratch resistance properties.

• High Volume farming equipment, transportation vehicles where stoving is difficult like Buses, Trailers, Railways Coaches, Earth moving equipment and Tractors.

• In Mansonary coatings where good alkali resistance and pore filling properties are required.

• Wood, Floor and Furniture coatings.
  

• Chemical, Fertilizer, OEM (original equipment manufacturer), storage tank, Petrochemical Industries and Refineries.

• On any substrate like Plastics, Metals, non-Metals, Fibre-glass, Aluminium.

• In ultra-violet Resistance coatings.

• Electrical fittings.
  
  TECHNICAL DATA :
  
  Generic Type : Two pack Polyurethane
  Finishes : Clear & Pigmented with high gloss, matt and Texturised finishes.
  Covering : 12 sq. mtr. Per litre on normal smooth surface at 25-30 micron film thickness.
  Mixing ratio : 70 parts Base with 30 parts of Hardner and/or as mentioned on container.
  Thinner : 25 to 30 parts recommended Thinner.
  Pot life : 2 to 4 hours after mixing with Hardner @ 30° c.
  Method of application : Spray, Airless spray or brush.
  Air Pressure : 25-40 lbs. Per sq. inch by spray depending upon type of assembly.

• Remove oil, grease, dirt, welding flux, mill scale, corrosion, products, oxides, loose particles by solvent cleaning or sand papering in case of metals.

• Clean and Dry surface.
  

• Level deformaties if any by application of N. C. Putty, Polyester Putty depending upon type of substrate.

• Carry out sanding with water emery paper and polish same to a fine finish.

• Apply one coat of Primer* and allow 8-12 hours of drying.

• Apply two coats of Polyurethane Paint at re-coat intervals of 8-12 hours.

"WOODLUX MELAMINE WOOD FINSISH" is two pack systems which is to be applied on wooden substrates to produce Glossy, semi-Glossy, matt finishes that enhance the life of wood to a great extent. Apart from its protective value, it exhibit excellent decorative finish on wooden substrate. The coating being transparent in nature, the natural structure of wood grains are visible their by the texture of wood is being preserved.

These novelty finishes are in great demand and highly recommended by architects and Interior Decorators. Incorporation of special ingredients makes it outstanding in domestic, industrial and marine applications.

Some of the features of this coatings are :
- Excellent drying characteristics.
- Excellent inter -coat adhesion.
- Smooth abrasion resistance film of high surface quality.
- High film transparency, no haze formation.
- Excellent scratch, marr, Impact resistance with high Flexibility
- Resistance to stain of Tea, coffee, Alcohol spillaqe.
- High resistance to water fungus attack.
- No formation of hard sediments during storage.

SPECIFICATIONS & TECHNICAL DATA
1) Viscosity @ 30 c on B4 cup           70 ± 10.
2) Wt /lit @ 30 c                               1.02 ± 0.01.
3) Finishes                                       Glossy & Matt.
4) Application                                   Wood & Wood Substrates.
5) Recommended Thinner                  TH - 1000
6) Covering capacity (Therotical)         8 to 10 sq.mt./lit/coat at 25 micron Film Thickness.
7) DRYING CHARACTERISTICS
                            Surface Dry          15 to 20 mts.
                            Tack Free             3.0 hours.
                            Hard Dry              24 hours.
8) Pot life                                         4-5 hours after mixing with hardner
9) Shelf Life                                      1 year from date of manufacture when stored in sealed containers.
10) Method of application                   Spraying.
11) Dry film Thickness                       20 to 25 micron.
12) Gloss at 60 Deq. gloss head        Glossy - 85 ± 5 (two coat)
                                                       Matt - 10 max
13) Hardness Test                             2H
14) Flexibility Test                             passes.
15) Crosscut Adhesion Test               passes.
16) Cissing Tendency                        No Cissing tendency.
17) Sanding Properties
(320 Emery paper)                            Satisfactory.
18) Inter coat Adhesion                      Passes.

Above Properties values represent typical results only and are not to considered specifications.

APPLICATIONS PROCEDURES FOR WOODLUX MELAMINE WOOD FINSISH.

FILLING :-
1) The wooden surface or furniture to be coated must be dry and free from dust and loose particles. Prepare the smooth surface by sanding with Emery Paper No.180 followed by fine sanding with Emery No. 320. Clean the surface free of loose particles and dust.
2) Apply wood filler with Putty knife or musclin cloth to smoothen minor unevenness of the surface and allow it to dry for 1-2 hours. Remove excess filler by Emery Paper No.320 to smooth finish.

SEALING :-
Apply one coat of Woodlux Natural Wood Finish clear sealer after mixing Base and Hardner with Thinner. Allow it to dry for 6-8 hours. Scuff it with Emery Paper No.320 to remove raised grains. If pores are still not filled, apply a second coat and follow the same step. Smooth sand the sealer coat after drying.
FINISH COAT :-
Select the finish coat available in Glossy or Matt, Semi-Glossy finish can be prepared by mixing Glossy and Matt in desired proportions.
Mix thoroughly Base and Hardner in recommended mixing ratio and thin down with thinner. Apply two coats. Allow 2-3 hours between coats. Allow the final finish coat to dry overnight. A completely clean surface in mandatory to ensure inter-coat adhesion, especially at long re-coat interval.
MIXING RATIO :-
Woodlux Natural Wood Finish clear sealer, Matt & Glossy are two pack system supplied as Base & Hardner.
Mix thoroughly 90 Parts of Base & 10 parts of Hardner by volume in plastic or gloss container stir the mixture thoroughly and strained through musclin cloth. Add 15 to 20 parts of Thinner the mixture should be used within 5-6 hours of mixing.
SPRAY APPLICATIONS & DRYING TIPS :
1) Recommended air pressure for spray application is 25-40 # 1bs per sq. inch depends upon type of assembly.

2) The Control of the amount, Pressure and cleanliness of the air going to the spray gun is of critical importance in the system as air contains small but harmful quantities of water, oil, dirt and other contaminants which will lessen the quality of the sprayed finish and the air will likely vary in pressure during spraying job.
Air Control regulator or Air transformer perform function of air filtering, cleaning, air pressure regulation and indication of Pressure.

3) Air Transformer and Compressor tank should be drained before starting spraying operation and if necessary more than once if humidity level in air is higher than normal.

4) This is air drying system with surface drying time of 15-20 min. and Hard dry of 24-48 hours.

SAFETY INSTRUCTIONS AND OTHER INFORMATIONS :

1) Spray finishing creates a certain amount of overspray, hazardous vapours and toxic fumes. This is true even under ideal conditions and there is no way to avoid it entirely.
For this reasons Respirators are essential during Spraying operation. Organic vapor Respirator with Protective goggles are recommended with spray Booth chambers.

2) This is a flammable material. Keep away from heat, sparks, etc. store in dry place with adequate ventilation.

3) Always stir contents well and strain through muslin cloths (white). Close the container tightly after removing required quantity of Base, Hardner and Thinner.

4) It is a must to use separate containers (glass or plastics) for weighing Base and Hardner. Do not transfer the mixed Paint (Base + Hardner) Back to original Base container as it will spoil whole paint in the containers.

5) It is recommended to mix only the required amount of Base and Hardner which is needed for spraying as the pot life of mixed Paint is low.

WORKING PROCEDURE FOR STOVING PAINTS :
DESCRIPTION : STOVING PAINT is a single component pain system with
excellent gloss and colour retention properties.

RECOMMENDED USE : As a FINISH COAT on substrate such as steel and zinc body
where light fastness and gloss retention are desired.

APPLICATIONS DETAILS :
a) Mixing Ratio : Mix 100 parts of STOVING PAINT with 15 to parts of
recommended Thinner in a glass or plastic container.
Mix thoroughly & strain through Muslin Cloth.
b) Substrates : Should be Dry and Clean. Pre-treatment of Phosphating with
subsequent coat of Primer is recommended.
c) Applications : Spraying.
d) Air Pressure : 25-40 lbs. per. sq. inch depends upon type of assembly.
e) Drying schedule : 20 minutes @ 120°C.
f) Remarks : Use recommended Thinner only.
g) Safety : As a general rule, avoid inhalation of solvent vapours or Paint mist and
contact of liquid Paint with skin & eyes. Provide forced ventilation when
working with solvent borne coating in confined spaces or stagnant air.
Provide respiratory, skin & eye protection. Follow local & national safety
regulations.

G. THANE POLYURETHANE PAINTS :
DESCRIPTION : G. THANE POLYURETHANE PAINT is a Two component Polyurethane
Paint (supplied as Base & Hardner) with Excellent gloss and colour
retention. It is resistant to water, impact, abrasion.

RECOMMENDED USE : As a finish coat on a variety of substrates such as
Steel, Aluminium, Zinc body. Gloss fibre reinforced
Polyester, Plywood & Hard wood where light fastness of
gloss retention are desired.
APPLICATION DETAILS :
a) Mixing Ratio : Mix 70 parts of Basic with 30 parts of Hardner in clean glass or
plastic container. Add 30 parts of Thinner & mix thoroughly.

b) Substrates : Should be dry & clean. Pretreatment of phosphating
with subsequent coat of Primer is recommended.

c) Pot Life : 2 to 4 hours after mixing hardner @ 30°C.
d) Application : Spraying.
e) Air Pressure : 25- 40 lbs per sq. inch depending upon type of assembly.
f) Dry to Touch : 3 - 4 hours @ 30°C.
g) Hard Dry : Over night.
h) Fully cured : 7 days @ 30°C.
i) Remarks : Hardner is sensitive to moisture, store in dry place. Keep the can or bottle tightly
closed after use.
j) Safety : As a general rule, avoid inhalation of solvent vapours or Paint mist and contact
of liquid Paint with skin & eyes. Provide forced ventilation when working with
solvent borne coating in confined spaces or stagnant air. Provide respiratory, skin
& eye protection. Follow local & national safety regulations.

W A R R A N T Y :

The information contained in this leaflets is based on our experience and laboratory tests and true to the best of our knowledge. However, no warranty, express or implied, arising out of the use of our product is given as the conditions of use are beyond the control of manufacturers of this product. Customers are advised to carry out their own tests to judge the suitability of our product for the recommended applications.

"WOOD PRIME" is a two - component solvent based penetration primer specially developed for Wood and Wood substrates. Important feature of WOODPRIME is that it facilitates good water resistance there by protecting wood against dimensional changes due to weathering conditions by proper sealing . Apart from this, the coating provides good toothing for topcoat adhesion with faster drying through more rapid solvent release.

SPECIFICATION & TECHNICAL DATA

1. Product Description

Polyester Amino Resin System

2. Viscocity @ 30 Degree C on B4

100 + 10 Sec

3. Wt/Lit @ 30 Degree C

1.13 + 0.02

4. Application

Wood Surface Only

5. Finish

Smooth Finish

6. Shade

White

7. Method of Application

Spray

8. Thinner Intake

20 to 25%

9. Pot Life

To be used within 2 hours after mixing with Hardner

10. Drying Characteristics Surface Dry

15 - 20 mts

2 hours

6 - 7 hours minimum

11. Recommended D.F.T

15 - 20 microns

12. Covering Capacity (Theoretical)

60 sq. ft/lit.

13. Recommended Finish Coat

Neotex Paint - Texturised

14. Shelf Life

6 months from date of manufacturing when
stored in sealed container.

15. Packing Available

1 / 4 / 20 Litres.

16. Tooth Top Coat Adhesion

Good

17. Sanding Properties

Satisfactory

The above properties values represent typical results only and are not to be considered specifications.

Two component POLYURETHANE Clear & Pigmented coating were developed keeping in mind ultimate requirements in protective and decorative application with enhanced performance properties like :-

• Good gloss retention unsurpassed by any other air drying system and can be highly recommended for high U. V. conditions.

• Good resistant to Acids, Alkalis, Salt spray, solvents, lubricants and weathering properties like saline and marine atmosphere.

• Ability to produce good films at room temperature equipment to those obtained from stoving paint with major gain in energy conservation.

• Coating are more abrasion resistance with long life flexibility, impact resistance, stain resistance, scratch resistance properties.

• Easy to apply and fast drying.

• Good dielectric properties.

And hence recommended as a "TOP COAT FINISH"

• In automotive Industry, particularly in the vehicle repair as it gives a more rapid hardening than other refinish paints with high gloss film with good scratch resistance properties.

• High Volume farming equipment, transportation vehicles where stoving is difficult like Buses, Trailers, Railways Coaches, Earth moving equipment and Tractors.

• In Mansonary coatings where good alkali resistance and pore filling properties are required.

• Wood, Floor and Furniture coatings. Chemical, Fertilizer, OEM (original equipment manufacturer), storage tank, Petrochemical Industries and Refineries.

• On any substrate like Plastics, Metals, non-Metals, Fibre-glass, Aluminium.

• In ultra-violet Resistance coatings.
  

• Electrical fittings.
  
  TECHNICAL DATA :

Generic Type : Two pack Polyurethane

Finishes : Clear & Pigmented with high gloss, matt and Texturised finishes.
Covering : 12 sq. mtr. Per litre on normal smooth surface at 25-30 micron film thickness.
Mixing ratio : 70 parts Base with 30 parts of Hardner and/or as mentioned on container.
Thinner : 25 to 30 parts recommended Thinner.
Pot life : 2 to 4 hours after mixing with Hardner @ 30° c.
Method of application : Spray, Airless spray or brush.
Air Pressure : 25-40 lbs. Per sq. inch by spray depending upon type of assembly.

DRYING
a. Surface Dry : 25-30 minutes @ 30°c.
b. Tack Free : 3-4 hours @ 30°c.
c. Hard Dry : 24 hours.
d. Fully cured : 7 days for solvent & chemical resistance when applied to metallic surface.
e. Recoat intervals : 8 - 12 hour

APPLICATIONS :

• Remove oil, grease, dirt, welding flux, mill scale, corrosion, products, oxides, loose particles by solvent cleaning or sand papering in case of metals.

• Clean and Dry surface.

• Level deformaties if any by application of N. C. Putty, Polyester Putty depending upon type of substrate.

• Carry out sanding with water emery paper and polish same to a fine finish.

• Apply one coat of Primer* and allow 8-12 hours of drying.

• Apply two coats of Polyurethane Paint at recoat intervals of 8-12 hours.

* Polyurethane Paint can be applied on properly Primed surface.

Surfacing of which done with suitable Primer listed below, depending upon type of substrate.

SAFETY INSTRUCTIONS AND PRECAUTIONS :

1. Spray finishing creates a certain amount of over-spray hazardous vapours. This is true even under ideal conditions and there is no way to avoid it entirely.

2. For this reasons Respirators are essential during spraying operations. Organic vapour Respirator with Protective goggles are recommended with spray booth chambers.

3. This is a flammable materials. Keep away from heat, sparks, etc., store in dry place with adequate ventilation.

4. Always stir contents well and strain through musclin cloth. Close the container tightly after removing required amount of Base Hardner, as it is sensitive towards moisture before coating.

5. It is a must to use separate containers (glass or plastic) for weighing Base and Hardner. Do not transfer the mixed Paint (Base + Hardner) back to original base containers as it will spoil whole paint in the container.

6. It is recommended to mix only the required amount of Base and Hardner which is needed for spraying, as Pot-life of mixed Paint is low.

W A R R A N T Y :

The information contained in this leaflets is based on our experience and laboratory tests and true to the best of our knowledge. However, no warranty, express or implied, arising out of the use of our product is given as the conditions of use are beyond the control of manufacturers of this product. Customers are advised to carry out their own tests to judge the suitability of our product for the recommended applications.

Two component POLYURETHANE Clear & Pigmented coating were developed keeping in mind ultimate requirements in protective and decorative application with enhanced performance properties like :-

• Good resistant to Acids, Alkalis, Salt spray, solvents, lubricants and weathering properties like saline and marine atmosphere.

• Ability to produce good films at room temperature equipment to those obtained from stoving paint with major gain in energy conservation.

• Coating are more abrasion resistance with long life flexibility, impact resistance, stain resistance, scratch resistance properties.

• Easy to apply and fast drying.

• Good dielectric properties.

• And hence recommended as a "TOP COAT FINISH"

• In automotive Industry, particularly in the vehicle repair as it gives a more rapid hardening than other refinish paints with high gloss film with good scratch resistance properties.
  

• High Volume farming equipment, transportation vehicles where stoving is difficult like Buses, Trailers, Railways Coaches, Earth moving equipment and Tractors.
  

• In Mansonary coatings where good alkali resistance and pore filling properties are required.
  

• Wood, Floor and Furniture coatings.
  

• Chemical, Fertilizer, OEM (original equipment manufacturer), storage tank, Petrochemical Industries and Refineries.
  

• On any substrate like Plastics, Metals, non-Metals, Fibre-glass, Aluminium.
  

• In ultra-violet Resistance coatings.
  

• Electrical fittings.

TECHNICAL DATA :

Generic Type : Two pack Polyurethane
Finishes : Clear & Pigmented with high gloss, matt and Texturised finishes.
Covering : 12 sq.mtr. Per litre on normal smooth surface at 25-30 micron film thickness.
Mixing ratio : 70 parts Base with 30 parts of Hardner and/or as mentioned on container.
Thinner : 25 to 30 parts recommended Thinner.
Pot life : 2 to 4 hours after mixing with Hardner @ 30° c.
Method of application : Spray, Airless spray or brush.
Air Pressure : 25-40 lbs. Per sq. inch by spray depending upon type of assembly.

DRYING :
a. Surface Dry        25-30 minutes @ 30°c.
b. Tack Free           3-4 hours @ 30°c.
c. Hard Dry             24 hours.
d. Fully cured          7 days for solvent & chemical resistance when applied to metallic surface.
e. Recoat intervals   8 - 12 hours.

APPLICATIONS :

a. Remove oil, grease, dirt, welding flux, mill scale, corrosion, products, oxides, loose particles by solvent cleaning or sand papering in case of metals.
b. Clean and Dry surface.
c. Level deformaties if any by application of N. C. Putty, Polyester Putty depending upon type of substrate.
d. Carry out sanding with water emery paper and polish same to a fine finish.
e. Apply one coat of Primer* and allow 8-12 hours of drying.
f. Apply two coats of Polyurethane Paint at recoat intervals of 8-12 hours.

* Polyurethane Paint can be applied on properly Primed surface.

Surfacing of which done with suitable Primer listed below, depending upon type of substrate.

SAFETY INSTRUCTIONS AND PRECAUTIONS :

1. Spray finishing creates a certain amount of overspray hazardous vapours. This is true even under ideal conditions and there is no way to avoid it entirely.

2. For this reasons Respirators are essential during spraying operations. Organic vapour Respirator with Protective goggles are recommended with spray booth chambers.

3. This is a flammable materials. Keep away from heat, sparks, etc., store in dry place with adequate ventilation.

4. Always stir contents well and strain through musclin cloth. Close the container tightly after removing required amount of Base Hardner, as it is sensitive towards moisture before coating.

5. It is a must to use separate containers (glass or plastic) for weighing Base and Hardner. Do not transfer the mixed Paint (Base + Hardner) back to original base containers as it will spoil whole paint in the container.

6. It is recommended to mix only the required amount of Base and Hardner which is needed for spraying, as Pot-life of mixed Paint is low.

W A R R A N T Y :

The information contained in this leaflets is based on our experience and laboratory tests and true to the best of our knowledge. However, no warranty, express or implied, arising out of the use of our product is given as the conditions of use are beyond the control of manufacturers of this product. Customers are advised to carry out their own tests to judge the suitability of our product for the recommended applications.

Two component POLYURETHANE Clear & Pigmented coating were developed keeping in mind ultimate requirements in protective and decorative application with enhanced performance properties like :-

• Good gloss retention unsurpassed by any other air drying system and can be highly recommended for high U. V. conditions.
  

• Good resistant to Acids, Alkalis, Salt spray, solvents, lubricants and weathering properties like saline and marine atmosphere.
  

• Ability to produce good films at room temperature equipment to those obtained from stoving paint with major gain in energy conservation.
  

• Coating are more abrasion resistance with long life flexibility, impact resistance, stain resistance, scratch resistance properties.
  

• Easy to apply and fast drying.
  

• Good dielectric properties.
  And hence recommended as a "TOP COAT FINISH"
  

• In automotive Industry, particularly in the vehicle repair as it gives a more rapid hardening than other refinish paints with high gloss film with good scratch resistance properties.
  

• High Volume farming equipment, transportation vehicles where stoving is difficult like Buses, Trailers, Railways Coaches, Earth moving equipment and Tractors.
  

• In Mansonary coatings where good alkali resistance and pore filling properties are required.
  

• Wood, Floor and Furniture coatings.
  

• Chemical, Fertilizer, OEM (original equipment manufacturer), storage tank, Petrochemical Industries and Refineries.
  

• On any substrate like Plastics, Metals, non-Metals, Fibre-glass, Aluminium.
  

• In ultra-violet Resistance coatings.
  

• Electrical fittings.
  
  TECHNICAL DATA :
  
  Generic Type                   Two pack Polyurethane
  Finishes                          Clear & Pigmented with high gloss, matt and Texturised finishes.
  Covering                          12 sq.mtr. Per litre on normal smooth surface at 25-30 micron film thickness.
  Mixing ratio                      70 parts Base with 30 parts of Hardner and/or as mentioned on container.
  Thinner                            25 to 30 parts recommended Thinner.
  Pot life                            2 to 4 hours after mixing with Hardner @ 30° c.
  Method of application       Spray, Airless spray or brush.
  Air Pressure                    25-40 lbs. Per sq. inch by spray depending upon type of assembly.

DRYING :
a. Surface Dry                        25-30 minutes @ 30°c.
b. Tack Free                          3-4 hours @ 30°c.
c. Hard Dry                            24 hours
d. Fully cured                         7 days for solvent & chemical resistance when applied to metallic surface.

Recoat intervals                      8 - 12 hours.

APPLICATIONS :

• Remove oil, grease, dirt, welding flux, mill scale, corrosion, products, oxides, loose particles by solvent cleaning or sand papering in case of metals.
  

• Clean and Dry surface.
  

• Level deformaties if any by application of N. C. Putty, Polyester Putty depending upon type of substrate.
  

• Carry out sanding with water emery paper and polish same to a fine finish.
  

• Apply one coat of Primer* and allow 8-12 hours of drying.
  

• Apply two coats of Polyurethane Paint at recoat intervals of 8-12 hours.

* Polyurethane Paint can be applied on properly Primed surface.

Surfacing of which done with suitable Primer listed below, depending upon type of substrate.

SAFETY INSTRUCTIONS AND PRECAUTIONS :

1. Spray finishing creates a certain amount of overspray hazardous vapours. This is true even under ideal conditions and there is no way to avoid it entirely.

2. For this reasons Respirators are essential during spraying operations. Organic vapour Respirator with Protective goggles are recommended with spray booth chambers.

3. This is a flammable materials. Keep away from heat, sparks, etc., store in dry place with adequate ventilation.

4. Always stir contents well and strain through musclin cloth. Close the container tightly after removing required amount of Base Hardner, as it is sensitive towards moisture before coating.

5. It is a must to use separate containers (glass or plastic) for weighing Base and Hardner. Do not transfer the mixed Paint (Base + Hardner) back to original base containers as it will spoil whole paint in the container.

6. It is recommended to mix only the required amount of Base and Hardner which is needed for spraying, as Pot-life of mixed Paint is low.

W A R R A N T Y :

The information contained in this leaflets is based on our experience and laboratory tests and true to the best of our knowledge. However, no warranty, express or implied, arising out of the use of our product is given as the conditions of use are beyond the control of manufacturers of this product. Customers are advised to carry out their own tests to judge the suitability of our product for the recommended applications.

The Concept of Hygiene Coating System.

MICROSEPTIC …

In order to provide the interior of a structure with effective protection against the growth of mould, bacteria, and other micro-organisms, a hygiene control system must provide a surface that is easy to clean, hard wearing and free from joints, seams and other features that might harbour dirt and bacteria.
Hygiene coatings represent one of the simplest and most effective means of achieving such a surface because they are quick and easy to apply, and provide a truly seamless finish regardless to the shape and the complexity of the substrate. As a result, they deny micro-organisms any hiding place and help facilities to comply with the stringent hygiene requirements.

• … is a tough, flexible, semi-gloss to gloss, waterborne polyurethane based coating.

What is MicroSeptic?

• … contains a non-leaching anti-microbial system & cures without any strong odour.

SETCO Chemicals (I) Pvt. Ltd. have developed MICROSEPTIC: a waterbased coating system incorporating non-leaching anti-microbial biocides that prevents growth of bacteria, mold, mildew and fungus on its surface. MICROSEPTIC is non-soluble, non-leachable, non-toxic, non-poisonous, and non-hazardous and stays permanently effective as long as MICROSEPTIC film remains exposed on the surface. The results: Lower life cycle costs and permanent "clean rooms".

• … Stays clean and resistant to attack by abrasives and cleaning agents.

Hygiene Standards.

• … tolerates thermal movement without cracking, splitting or flaking.

The high standards demanded for wall and ceiling finishes need not be cause of concern any more, being strictly achieved using SETCO MICROSEPTIC anti-bacterial hygiene coating.

• … is colour stable and resists UV induced embrittlement.

This coating upgrades surfaces to a standard, which cannot be paralleled by conventional paints or ceramic tiles, however carefully grouted. Conventional paints are liable to crack and flake, due to the high humidity prevailing in such environments.

• … ideal for use internally or externally on walls, ceilings, insulation and most other building materials.

SETCO MICROSEPTIC anti-bacterial hygiene coating is safe and easy to use and designed to confer lasting hygiene controls, whilst reducing maintenance costs.

• … produces extra smooth finish a normal requirement for clean rooms.

SETCO MICROSEPTIC anti-bacterial hygiene coating is flexible, resisting embrittlement and flaking and offers a practical and durable solution to even the most persistent hygiene problem.

Kitchen …

MICROSEPTIC stops bacteria from growing on metal, concrete & asbestos walls and ceiling. It has no toxic elements in the film.

• HARD WEARING:
  MICROSEPTIC resists staining and washing down. Exceptionally tough with impact resistance gloss.
  

Surgical Theatre …

MICROSEPTIC is specially developed to combine the high technology benefits, with an attractive finish that totally outmatches most of the best gloss paints. MICROSEPTIC is without equal, bringing together advanced anti-microbial chemistry and coating technology to provide a new generation coating that meets the most exacting hygiene requirements.

• HIGH STANDARD OF HYGIENE & DECORATIVE FINISH: State-of-the-art high technology benefits MICROSEPTIC with an attractive and long lasting finish.

Bottling Plant …

MICROSEPTIC cures to a smooth finish, which can be regularly washed down without damage to the coating. MICROSEPTIC is waterbased and free from heavy odour during application. When applied in a proper manner, it can have a life at least three times longer than conventional paints and is available in a wide range of colours.

• EASE OF MAINTENANCE: MICROSEPTIC will not support the growth of micro-organisms, dirt build-up and nutrients. Regular cleaning should be undertaken. Use detergents, scrubbers, and scouring powder or steam cleaning.

RECOMMENDED APPLICATIONS :…

• Homes: Bathrooms - controls mildew & moulds, Kitchen - stops bacteria from growing
  

• Medical: Hospital Kitchens, Operating Surgical Theatres, In-Patient Rooms, Doctor's Offices and Examination Rooms, Pharmacies, Maternity Homes, Nursing Homes
  

• Industrial & Commercial Premises: Toilets & Rest Rooms, Waiting Rooms, Office Block, School & College Passages, Toilets
  

• Food & Beverage Bottling Plants, Mineral Water Plants, Brewery, Dairy
  

• Plants Manufacturing Pharmaceutical & Personal Hygiene Products, Quality Control & Testing Laboratories
  

• Restaurant & Hotel Kitchens, Laundry Room, Butcher Shop, Meat Packaging Units, Cafeterias, Groceries
  

In order to provide the interior of a structure with effective protection against the growth of mould, bacteria, and other micro-organisms, a hygiene control system must provide a surface that is easy to clean, hard wearing and free from joints, seams and other features that might harbour dirt and bacteria.

Hygiene coatings represent one of the simplest and most effective means of achieving such a surface because they are quick and easy to apply, and provide a truly seamless finish regardless to the shape and the complexity of the substrate. As a result, they deny micro-organisms any hiding place and help facilities to comply with the stringent hygiene requirements.

MICROSEPTIC is a tough, flexible, semi-gloss to gloss finish; waterborne polyurethane based coating, which contains a non-leaching anti-microbial system. MICROSEPTIC cures without any strong odour to form an attractive, finish which stays easy to clean and resistant to attack by abrasives and other cleaning agents. It develops its strength and other key physical properties extremely quickly and cures without the release of any harmful solvents or heavy odour. MICROSEPTIC will tolerate thermal movement without cracking, splitting or flaking, and, due to its inherent vapour permeability, allows substrate moisture to escape without causing blisters beneath the cured film. It is colour stable, resists UV induced embrittlement and dries rapidly that two coats can be applied on the same day.

MICROSEPTIC uses :
MICROSEPTIC is ideal for use internally or externally on walls, ceilings, insulation and most other building materials. It can also be applied to vessels, tanks and associated equipment, and where positive pressure is essential like in fruit storage.

The use of MICROSEPTIC is suitable to prevent fungicidal deterioration occurring on wall surfaces in food & pharmaceutical manufacturing plants, kitchens and hospital walls and on any structural surface in buildings where a high standard of hygiene is necessary.

The normal applications that MICROSEPTIC is used for is best served by White and tinted colours like Cream, Magnolia, Mushroom, Pale Lemon, Lt. Blue, Lt. Green & Lt. Grey. The natural weathering process of MICROSEPTIC may cause slight darkening of the colours. All colours are intermixable.

SURFACE PREPARATION:
Remove oil and grease with detergent and water, and laitance from the substrate by wire brushing. Remove loose materials by either wire brushing or high pressure water lancing. Ensure all surfaces are clean and free from dampness. Treat mould with "Anti-fungal Wash", and algae with bleach.

When applying on Brick, Blockwork, Concrete, Plaster, Asbestos Cement, Lining Boards, Insulation, Previously Painted Surfaces, Bitumen Surfaces, Mastics & Timber, use SETCO ELASTOPRIME as a bonding primer prior to the application of MICROSEPTIC. When applying on Metal surfaces, use SETCO METALGRIP as primer-sealer.

APPLICATION PRECEDURE:
Cracks, not liable to movement should be filled with external grade, flexible plaster sealer. Apply MICROSEPTIC over a suitable primer as explained above. For absorbent surfaces, MICROSEPTIC may be diluted with 25% of clean potable water as a primer to kill suction. Dusty friable substrates require sealing with SETCO ELASTOPRIME. When applying MICROSEPTIC over Painted Surfaces, ensure existing paints are fully adhered before priming. Remove existing paint if not well adhered. Apply MICROSEPTIC directly over well-sanded gloss, emulsion, alkyd and epoxy paints. For safety, use SETCO ELASTOPRIME or SETCO METALGRIP prior to applying MICROSEPTIC.

Apply both coats of MICROSEPTIC at a Wet Film Thickness of 275 microns each to obtain 325 microns Dry Film Thickness. The cured film thickness is essential to the long-tern durability and general effectiveness of the coating. It is important that the Dry Film Thickness is obtained.

Coverage rates provided are for smooth non-absorbent surfaces. Please provide adequate allowances for uneven or absorbent surfaces and wastage.

To produce an extra smooth finish with MICROSEPTIC, a normal requirement for clean rooms, operating theatres, etc. use airless spray. This aids strict hygiene control and facilitates cleaning when frequent sterilization is required.
Do not apply MICROSEPTIC near foodstuffs in unventilated conditions. Do not thin or brush out like conventional paints.

Semi Gloss to Gloss

1.5 to 1.75 Liter per Sq. Mt., at 325 microns dry film thickness

White tintable to Cream, Magnolia, Mushroom, Pale Lemon, Lt. Blue, Lt. Green, Lt. Grey or as desired

1 hour

Proprietary Dispersions of Polyurethane & Acrylic

After 4 hours

50 % +/- 10% Depending on shade and gloss

5 to 7 days

4 litres and 20 litres

THERMSHIELD is a highly engineered, elastomeric, insulating, waterproof Coating incorporating Hollow Ceramic Microspheres for Thermal Reflection & Insulation. A waterborne, high-build formula that reflects the Sun's radiant heat, insulates, soundproofs, beautifies and protects, THERMSHIELD is characterized by excellent adhesion to most substrates, high weather resistance, UV stability, elasticity and toughness. THERMSHIELD forms a thick rubberlike shield of protection that expands and contracts with varying hot and cold temperatures, plus resists thermal shock. The most important feature of THERMSHIELD is its heat refractive, reflective and dissipative properties.

Secondary features include its elastomeric properties, resistance to microbial growth, fire and corrosion resistance properties. THERMSHIELD offers superior mildew resistance, insulation, excellent adhesion, ultraviolet reflection and a beautiful finish.

THERMSHIELD is designed as an insulating, energy saving coating that combats the destructive environmental forces of nature. An inexpensive solution to roof & sidewall maintenance, that is easy to apply and requires very little maintenance. THERMSHIELD will provide years and years of durable protection and outstanding aesthetics, and extend substrate & structure life.